## How much does it cost to pave a 2000 sq ft driveway?

Paving an asphalt driveway costs \$4,721 on average, with a typical range between \$2,930 and \$6,560.

This project runs \$7 to \$13 per square foot, including \$2 to \$6 per square foot for materials and \$5 to \$7 per square foot for labor.

If you need replacement, you’ll pay \$8 to \$15 per square foot..

## Is 2 inches of asphalt enough for a driveway?

For a regular driveway which is going to be used by regular cars, bicycles and bikes; 2 inches of asphalt is thick enough. Generally for resurfacing, 2 inches of asphalt is just about right, but if you are going for a stone surface and need a good base, it is better to layer up the asphalt thicker, around 3 inches.

## What is the cheapest way to pave a driveway?

Of the four paving materials described in this guide, aggregate (gravel) is the least expensive, followed by asphalt, concrete, and paving stones. If you’re installing your driveway on a shoestring budget, gravel is your best choice. If you have more wiggle room, you’ll have more choice.

## How much does it cost to pave 1 acre?

The PAVE-A-LOT works just as well as the expensive units but sells for a fraction of the cost. Every aspect of the PAVE-A-LOT is easy to learn and the paving can be done at your convenience. This method of paving will save you at least half the cost, which is about \$10,000.00 to \$12,000.00 per acre.

## How many square feet will 1 ton of asphalt cover 2 inches thick?

80 square feetOne ton of asphalt covers about 80 square feet with 2 inches of material or 160 square feet with 1 inch of material.

## How do I calculate how much asphalt I need?

How to Calculate Asphalt TonnageUse a tape measure to determine distances. … Convert the length, width and height measurements to feet by dividing by 12, since each foot contains 12 inches. … Multiply the length times the width times the depth to obtain the volume in cubic feet of the space to be paved.More items…

## How many tons of asphalt are in a truck load?

exact tare weight of the truck is known when weigh batchers or back-way systems are used, a truck can be loaded safely to its legal limit each round. The truck cycle in Figure 10 looks much like the one in Figure 8, but now trucks are loaded with 21 tons of mix instead of 20.

## How much does it cost to pave a 100 foot driveway?

Other sources estimate the cost to install an asphalt driveway to be between \$2,300 and \$10,300. Homeowners typically pay per square foot. Reibling adds the average cost per square foot is between \$3.50 and \$4.50. Some asphalt contractors may charge by the ton, with the cost ranging from \$100 to \$150 per ton.

## How many square feet will a ton of asphalt cover?

The density of asphalt is generally given at 140 lbs per cubic foot (I have assumed you would like this in imperial as you use feet) At that density a ton ( 2240 lbs) is 16 cubic feet so it now comes down to how thick you want the coating, at 1 inch thick the ton will cover 12 x 16 (192) square feet.

## Is 2.5 inches of asphalt enough for a driveway?

Thus, a compacted asphalt thickness of 2.5 to 3 inches may be more than sufficient for a residential driveway, but a busy mixed-use lot may need a compacted asphalt thickness of 4 inches or more.

## How much is a ton of asphalt millings?

Asphalt Millings Cost Per Ton One ton of asphalt millings covers 80 square feet at a few inches thick. A ton costs between \$7 and \$60, depending on the amount of recycled asphalt pavement in the mixture. The fewer recycled materials the more expensive the mix.

## How much does a dump truck load of asphalt cost?

The average price of good quality asphalt is \$85 to \$150 per ton. Similarly, you may ask, how much is a dump truck load of asphalt? A concrete driveway 90 feet long and ten feet wide would be around \$1800 for materials plus an additional \$2000 or so for labor, for a total cost of nearly \$4000.